Life Fitness Home Gym 829 User Manual

829 LEG CURL/EXTENSION  
WARNING:  
Read and follow all directions  
for each step to insure proper  
assembly of this product.  
USER’S GUIDE  
CLASS H  
PART # 7078201  
REV. B  
1
Version: 829107  
Revision: 06/26/01  
 
IMPORTANT NOTES  
Please note:  
* Thank you for purchasing the ParaBody 829 LEG CURL/EXTENSION. Please read these  
instructions thoroughly and keep them for future reference. This product must be assembled  
on a flat, level surface to assure its proper function.  
* This product must be assembled on a flat, level surface to assure its proper function. DO NOT  
securely tighten any frame connections until the entire frame has been assembled, unless  
otherwise stated.  
Tools Required forAssembly  
* 3/4” wrench  
* 9/16” wrench  
* Ratchet with 3/4” and 9/16” sockets  
* Adjustable wrench  
* Tape measure  
Bolt Length Ruler  
NOTE: BOLT LENGTH IS MEASURED FROM THE UNDERSIDE OFTHE HEAD OFTHE BOLT.  
BOLT LENGTH  
BOLT LENGTH RULER:  
1/2  
1/2  
1/2  
1/2  
1/2  
1/2  
0
1
2
3
3
4
5
6
 
1’  
2’  
3’  
4’  
5’  
1’  
2’  
3’  
4’  
5’  
6’  
1 Square = 1’ X 1’  
4
 
PARTS LIST  
KEY PART #  
DESCRIPTION  
FRONT SUPPORTTUBE  
BACK PADADJUST TUBE  
BACK PAD SUPPORTTUBE  
1-3/4 SQ X 5" TUBE  
1-3/4 SQ X 13-1/2" TUBE  
LEG CURL/EXTENSION  
BACK PADASSY  
QTY  
1
KEY PART #  
DESCRIPTION  
3/8 X 3" BOLT  
QTY  
8
1
2
3
4
5
6
7
8
9
6259108  
6625402  
6625502  
6216702  
6668202  
6662002  
6661221  
6661621  
6662208  
20 3102904  
21 3102906  
22 3102917  
23 3202102  
24 3102501  
25 3102802  
26 3102804  
27 3102807  
28 6405201  
29 6692601  
30 3102416  
31 6406401  
32 3104301  
33 6416601  
34 6020601  
35 3105401  
36 3103101  
37 6467001  
1
3/8 X 4" BOLT  
2
1
1/2 X 4" BOLT  
1
1
1/2 X 7" BOLT  
1
1
3/8" FLAT WASHER  
3/8" NYLOCK NUT  
1/2" LOW HT. NYLOCK NUT  
3/8" LOW HT. NYLOCK NUT  
2" SQ END CAP  
20  
4
1
1
2
SEATPADASSY  
1
2
LEG EXT HANDLE RHT  
LEG EXT HANDLE LFT  
LEG FRAME  
1
3
10 6662308  
11 6668508  
12 6668808  
13 6125101  
14 6549301  
15 6194601  
16 6628302  
17 6412001  
18 6466901  
19 3102909  
1
3 X 2" END CAP  
2
1
2 X 1" END CAP  
4
REAR BASE LEG  
1
HINGE TAB  
2
3/4 X 16" TUBE  
2
3/4" SQ RUBBER BUMPER  
1-1/2 X 3/4" GLIDE (QTY 8)  
1/2" FLANGE BEARING  
STARLOCK COLLAR  
1-1/4 X 5" GRIP  
1
3/4 X 17" TUBE  
1
2
4 X 7" ROLLER PAD  
1/8 X 2 X 8" PLATE  
3/8” DIA SPRING PIN  
1/2" DIA SPRING PIN  
3/8 X 1" BOLT  
6
2
1
6
2
4
1
PARABODY LOGO END CAP  
4
4
LEG EXTENSION  
LEG CURL  
5
 
36  
12  
37  
STEP 1: Insert four PARABODY LOGO END  
CAPS(37) into the ends of REAR BASE  
LEG (12) and FRONT BASE SUPPORT  
(1). See FIGURE 1.  
1
37  
STEP 2: Slide two 1-1/4 x 5” GRIPS (36) over tubes  
on REAR BASE LEG (12). See FIGURE  
1.  
FIGURE 1  
12  
11  
25  
STEP 3: Securely assemble REAR BASE LEG (12)  
to LEG FRAME (11) using two 3/8 X 3”  
BOLTS (20), four 3/8” FLAT WASHERS  
(24), and two 3/8” NYLOCK NUTS (25).  
See FIGURE 2.  
24  
24  
20 3/8 X 3”  
FIGURE 2  
11  
STEP 4: Securely assemble FRONT BASE SUP-  
PORT (1) to LEG FRAME (11) using two  
3/8 X 3” BOLTS (20), four 3/8” FLAT  
WASHERS (24), and two 3/8” NYLOCK  
NUTS (25). See FIGURE 3.  
1
25  
24  
24  
3/8 X 3” 20  
FIGURE 3  
9
10  
&
STEP 5: Slide two 1-1/4 X 5" GRIPS (36) over  
RIGHT LEG EXT HANDLE (9) & LEFT  
LEG EXT HANDLE (10). See FIGURE 4.  
36  
FIGURE 4  
6
 
FIGURE 5  
27 LOW HEIGHT  
24  
29  
STEP 6:Securely assemble RIGHT (9) & LEFT (10)  
LEG EXTHANDLES to LEG FRAME (11)  
using two 3/8 X 4” BOLTS (21), four 3/8”  
FLATWASHERS (24) , and two 3/8” LOW  
HEIGHT NYLOCK NUTS (27). See FIG-  
URE 5.  
10  
29  
11  
STEP 7:Insert two 3 X 2” END CAPS (29) into  
9
the leg frame as shown in FIGURE 5.  
24  
18  
21 3/8 X 4”  
FIGURE 6  
STEP 8:Securely assemble one 1/2” SPRING PIN AS-  
SEMBLY (18) into the spring pin barrel on the  
LEG FRAME (11) as shown in FIGURE 6.  
11  
FIGURE 7  
2
STEP 9:Insert four 2 X 1” END CAPS (30) into the ends  
of the BACK PAD ADJUST TUBE (2) & BACK  
PAD SUPPORT TUBE (3). See FIGURE 7.  
3
30  
1/2  
1/2  
1/2  
1/2  
1/2  
1/2  
0
1
2
3
4
5
6
7
 
FIGURE 8  
STEP 10: Securely assemble BACK PAD ADJUST  
TUBE (2) & BACK PAD SUPPORT TUBE  
(3) to LEG FRAME (11) using one 1/2 X 7”  
BOLT (23) and one 1/2” LOW HEIGHT  
NYLOCK NUT (26). (NOTE: SECURELY  
TIGHTEN BOLT THEN BACK NUT OFF  
1/4 TURN TO ALLOW THE TWO PARTS  
TO ROTATE FREELY.) See FIGURE 8.  
3
26  
2
11  
23 1/2 X 7”  
FIGURE 9  
STEP 11: Securely attach the BACK PAD (7)  
to the BACK PAD TUBES (2 & 3)  
using four 3/8 X 3” BOLTS (20)  
and four 3/8” FLAT WASHERS  
(24). See FIGURE 9.  
20 3/8 X 3”  
3
24  
7
2
FIGURE 10  
19 3/8 X 1”  
24  
16  
STEP 12: Securely fasten 2 X 8” PLATE (16) to bottom of SEAT  
PAD (8) using two 3/8 X 1” BOLTS (19) and two 3/8”  
FLAT WASHERS (24). See FIGURE 10.  
8
8
 
31  
FIGURE 11  
STEP 13: Slide two HINGE TABS (31) over posts on  
LEG FRAME (11). See FIGURE 11.  
11  
31  
FIGURE 12  
8
STEP 14: Securely attach the SEAT PAD (8) to the  
HINGE TABS (31) using two 3/8 X 1”  
BOLTS (19) and two 3/8” FLAT WASH-  
ERS (24). See FIGURE 12.  
31  
24  
19 3/8 X 1”  
STEP 15: Attach two ROLLER PADS (15) to the  
LEG FRAME (11) using one 17” ROLLER  
PAD SHAFT (14) and two STARLOCK  
COLLARS (35). See FIGURE 13.  
35  
15  
11  
14  
15  
35  
FIGURE 13  
1/2  
1/2  
1/2  
1/2  
1/2  
1/2  
0
1
2
3
9
4
5
6
 
4
5
33  
STEP 16: Attach eight 1-1/2” X 3/4” GLIDES (33) to 5”  
ROLLER PAD ADJUSTER (4) and attach eight  
1-1/2” X 3/4” GLIDES (33) to 13-1/2” ROLLER  
PAD ADJUSTER (5) as shown in FIGURE 14.  
FIGURE 14  
6
STEP 17: Securely assemble two 3/8” SPRING PIN AS-  
SEMBLIES (17) into the spring pin barrels on  
the LEG CURL/EXTENSION (6) as shown in  
FIGURE 15.  
17  
17  
FIGURE 15  
28  
6
4
STEP 18: Insert 5” & 13-1/2” ROLLER PAD  
ADJUSTERS (4 & 5) in the ends of the  
LEG CURL/EXTENSION (6). Pull back  
on SPRING PINS until ROLLER PAD  
ADJUSTERS (4 & 5) lock in place. See  
FIGURE 16.  
28  
STEP 19: Insert three 2” SQUARE END CAPS (28)  
into the ends of the LEG CURL/EXTEN-  
SION (6). See FIGURE 16.  
5
28  
FIGURE 16  
10  
 
STEP 20:Insert two 1/2” FLANGE BEARINGS  
(34) into the LEG CURL/EXTENSION  
(6). See FIGURE 17.  
26 LOW HEIGHT  
STEP 21:Securely assemble LEG CURL/EX-  
TENSION (6) to LEG FRAME (11)  
using one 1/2 X 4” BOLT (22) and one  
1/2” LOW HEIGHT NYLOCK NUT  
(26). (NOTE: SECURELY TIGHT-  
EN BOLT THEN BACK NUT OFF  
1/4 TURN TO ALLOW THE PART  
TO ROTATE FREELY.) See FIG-  
URE 17  
6
34  
11  
32  
22 1/2 X 4”  
STEP 22:Attach one 3/4” SQUARE RUBBER  
BUMPER (32) between the contact point  
of the LEG CURL/EXTENSION (6) and  
the LEG FRAME (11).See FIGURE 17.  
FIGURE 17  
STEP 23:Attach four ROLLER PADS (15) to the LEG CURL/EXTENSION (6) using two 16”  
ROLLER PAD SHAFTS (13) and four STARLOCK COLLARS (35). See FIGURE 18.  
35  
15  
THIS CONCLUDES THEASSEMBLY  
13  
OF THE PARABODY 829  
LEG CURL/EXTENSION  
6
FIGURE 18  
1/2  
1/2  
1/2  
1/2  
1/2  
1/2  
0
1
2
3
4
5
6
11  
 
MAINTENANCE  
Please note:  
* We recommend cleaning your product (pads and frame) on a regular basis, using warm soapy  
water. Touch-up paint can be purchased from your ParaBody customer service representative  
at (800) 328-9714.  
* Inspect equipment daily. Tighten all loose connections are replace worn parts immediately.  
Failure to do so may result in serious injury  
* PLEASE RECORD THE INFORMATION REQUESTED BELOW. IN THE EVENT  
YOU MAY NEED SERVICE YOU WILL BE ASKED FOR THIS INFORMATION.  
REMEMBER TO FILL OUT YOUR WARRANTY REGISTRATION CARD AND  
MAIL BACK.  
MODEL #________________________  
SERIAL #_________________________  
DATE OF PURCHASE: _____________  
DEALERS NAME: _________________  
DEALERS PHONE #_______________  
Thank you for purchasing the ParaBody 829 LEG CURL/EXTENSION.  
12  
 
LIMITED WARRANTY  
ParaBody extends the following LIMITED WARRANTY to the original owner of the ParaBody products. The Warranty terms apply to IN HOME USE ONLY.  
1. LIMITED WARRANTY ON FRAMEAND WELDS. If the frame of the ParaBody product or a weld should crack or break, it will be repaired  
or replaced by ParaBody. Terms: Lifetime – for so long as the Customer owns the ParaBody product.  
2. LIMITED WARRANTY ON PARTS. If the following parts are defective in material or workmanship, ParaBody will supply replacement parts:  
all bolts, nuts, washers, bearings, bushings, pulleys, thumbscrews, collars, cable retaining clips, adjustable pre-stretch slides, roller pad  
shafts, allen head bolts, weight selector pin, weight stack shaft, set screws, protector caps, adjustment chain, cotter pin, plunger, spring  
and knob. Terms: Lifetime – for so long as the Customer owns the ParaBody product.  
3. LIMITED WARRANTY ON CABLES AND UPHOLSTERY. If the coated cables or upholstery are defective in material or workmanship,  
ParaBody will repair or replace them, at its option. Terms: Three (3) years.  
4. CONDITIONSAND EXCEPTIONS. Any product misuse, abuse or alteration, any attempt to repair by a person other than an authorized  
ParaBody Service Center, any improper assembly, accident, or any other condition resulting from occurrences beyond the control of  
ParaBody will void this Limited Warranty.  
5. REPLACEMENT AND REPAIR EXPENSES. ParaBody will provide only replacement parts or repair under this warranty. The Owner is  
responsible for all other costs. Such costs may include, but are not limited to: a. labor charges for service, removal, repair or reinstallation  
of the ParaBody product or any component part; b. shipping, delivery, handling and administrative charges for returning parts to ParaBody;  
and c. all necessary or incidental costs related to installation of the replacement parts.  
6. SHIPPING. If shipping by the Owners is deemed necessary (in sole discretion of ParaBody), parts should be shipped in their original carton  
or equivalent packaging, fully insured with shipping charges prepaid. ParaBody will not assume any responsibility for any loss or damage  
incurred in shipping.  
7. CLAIM PROCEDURES. If service on your ParaBody product is required during the warranty period, please contact our Customer Service  
Department at 1-800-328-9714 for instructions regarding returning or replacing parts. Please have available the following information: (i) the  
dealer’s name; (ii) the date of purchase; (iii) the serial # (s) of your product (the serial number location is called out on the final assembly  
drawing included with your assembly instruction); (iv) a description of the nature of the problem.  
8. OWNER’S RIGHT. This Limited Warranty gives you specific legal rights. You may also have other rights, which vary depending on local law.  
9. LIMITATION OF IMPLIED WARRANTIES. All implied warranties, except to the extent prohibited by applicable law, shall have no greater  
duration than the warranty period set forth above. There are no warranties which extend beyond the description in this Limited Warranty.  
Because local laws do not allow limitations on how long an implied warranty lasts, the above limitations may not apply to you.  
10. DISCLAIMER. No other express warranty has been made or will be made on behalf of ParaBody with respect to any ParaBody product or  
the operation, repair or replacement of any ParaBody product. ParaBody shall not be responsible for injury, loss of use of the ParaBody  
product, inconvenience, loss or damage to personal property, whether direct or indirect, and incidental or consequential damages, so the  
above limitation or exclusion may not apply to you.  
NOTES:  
13  
 
LIFE FITNESS  
14150 Sunfish Lake Blvd. Ramsey Minnesota, 55303 U.S.A.  
Tel: 763.323.4500 Fax: 763.323.4797  
800.328.9714 (Toll-free within the U.S. and Canada)  
INTERNATIONALOFFICES  
Life FitnessAtlantic BV  
Life Fitness (UK) Ltd.  
QueenAdelaide  
Ely, Cambs CB7 4UB  
United Kingdom  
Phone CSS: (01353) 665507  
Fax CSS: (01353) 666719  
Atlantic Headquarters  
Bijdorpplein 25-31  
2992 LB Barendrecht  
The Netherlands  
Phone: (180) 646 666  
Fax: (180) 646 703  
Life Fitness EUROPE GmbH  
Siemensstrasse 3  
Life Fitness Benelux N.V.  
Bijdorpplein 25-31  
85716 Unterschleissheim  
Germany  
2992 LB Barendrecht  
The Netherlands  
Phone: (089) 31 77 51-0  
Fax: (089) 31 77 51 99  
Phone: 31 (180) 64 66 69  
Fax: 31 (180) 64 66 99  
Life Fitness Japan  
8/F, Nippon Brunswick Building  
5-27-7 Sendagaya  
Shibuya-Ku, Tokyo 151-0051  
Japan  
Phone: 81 (3) 3359-4309  
Fax: 81 (3) 3359-4307  
Life Fitness Italia S.R.L.  
Via Elvas 92  
39042 Bressanone  
Italy  
Phone: 39 (472) 835-470  
Fax: 39 (472) 833-150  
Life Fitness Do Brazil  
Al. Rio Negro, 433-Predio 2-Sala 2  
3º andar (Confab)  
Aplhaville-Barueri-Sao Paulo  
CEP: 06454-904  
Life FitnessAsia Pacific Limited  
Room 2610, Miramar Tower  
132 Nathan Road, Tsimshatsui  
Kowloon, Hong Kong  
Phone: (852) 2891-6677  
Fax: (852) 2575-6001  
Brazil  
Phone: 55 (11)7295-2217  
Fax: 55 (11) 7295-2218  
Download from Www.Somanuals.com.1A4ll Manuals Search And Download.  

Lenovo Tablet 064652U User Manual
Magnavox CD Player AZ 7433 User Manual
Makita Grinder GA7030 User Manual
Makita Impact Driver BTW150 User Manual
Marantz Stereo Receiver SR4120 User Manual
Master Lock Saw MK 470 User Manual
M Audio Computer Monitor SESSION User Manual
M Audio Speaker SBX User Manual
Maxtor Computer Drive 5T010H1 User Manual
Memorex VCR MVR041 User Manual